2.36 Inch SS304 Welded Wire Mesh Panel: Specifications, Applications, and Buying Guide

A 2.36 inch SS304 welded wire mesh panel is a stainless steel grid made by resistance-welding intersecting wires, with “2.36 inch” describing a mesh dimension that must be confirmed before ordering. It may refer to the clear opening or the wire spacing measured from center to center; these are not interchangeable. At Shunqiang Wire Mesh, we recommend confirming the measurement basis, wire diameter, panel size, and service environment before requesting a quotation. This guide explains the specifications, application fit, and purchasing checks that help B2B buyers define the right panel.

Read more

Key Takeaways

• Confirm whether 2.36 inches means clear opening or center-to-center pitch; the difference affects usable opening size.
• SS304 is a common general-purpose stainless steel choice, but suitability depends on moisture, chemicals, cleaning methods, and exposure to chlorides.
• Specify wire diameter, panel dimensions, edge finish, quantity, and any fabrication needs alongside the mesh size.
• Ask suppliers to confirm the drawing, tolerances, packaging, minimum order quantity, and lead time before placing an order.

What Is a 2.36 Inch SS304 Welded Wire Mesh Panel?

This panel consists of longitudinal and transverse stainless steel wires joined at their intersections by welding. Its rigid grid can be supplied as a flat panel for fabrication, screening, guarding, separation, or other project-specific uses. SS304 identifies the stainless steel grade, while 2.36 inches identifies one mesh dimension whose exact definition should appear on the drawing or specification sheet.

The conversion is 2.36 inches = 59.94 millimeters, commonly rounded to 60 millimeters for specification discussions. That conversion alone does not establish the clear aperture. A 60 mm center-to-center pitch, for example, produces a smaller clear opening because each wire occupies part of that distance.

Specifications to Confirm Before Ordering

Mesh Measurement and Opening

Ask the supplier to state whether the quoted dimension is the clear opening, wire pitch, or another measurement convention. If the required dimension is center-to-center pitch, the approximate opening can be calculated by subtracting the wire diameter from the pitch. For example, a 60 mm pitch with 3 mm wires gives an approximate clear opening of 57 mm; this is an illustrative calculation, not a fixed specification for every panel.

Include a dimensioned drawing when the panel must fit a frame, machine, or existing installation. The drawing should identify measurement direction, mesh count or spacing in both directions, and whether the first wire sits at a defined distance from the panel edge. These details reduce the risk of receiving a panel that matches the nominal mesh size but does not fit the assembly.

Wire Diameter, Panel Size, and Finish

Wire diameter influences panel weight, rigidity, open area, and fabrication requirements. A heavier wire may be appropriate where the panel needs greater stiffness, but it can also reduce the available opening when pitch remains unchanged. We recommend selecting wire diameter based on the panel’s function and support arrangement rather than choosing by appearance alone.

Specify overall length and width, edge condition, and any required cutting, bending, framing, or additional fabrication. Also clarify whether the panel is supplied with plain cut edges or a finished perimeter. Finish expectations should account for the application, since welding and subsequent handling can affect surface appearance and may require agreed finishing steps.

Material and Service Environment

SS304 is commonly selected for general-purpose corrosion resistance and fabrication, but it is not a universal choice for every environment. Exposure to salt, chlorides, strong chemicals, or frequent washdown may call for a material review before purchase. Where corrosion consequences are significant, provide the supplier with details of the operating environment and consider whether an alternative grade or protective design is more appropriate.

For traceability, specify the material grade in the purchase documents and ask what material documentation can be provided with the order. Do not assume that a generic “stainless steel” description confirms a particular grade or document package. Match the required paperwork to your internal quality process and project requirements.

Applications and Material Options

A 2.36 inch mesh dimension creates relatively open spacing compared with fine filtration mesh. Depending on wire diameter, panel size, and the system design, the grid may be considered for partitions, equipment guards, storage dividers, support panels, agricultural structures, or architectural and fabrication projects. These are possible application categories, not a guarantee that one panel specification is suitable for every use within them.

With competitive price and timely delivery, Shunqiang Wire Mesh sincerely hope to be your supplier and partner.

For applications involving screening or separation, compare the clear opening with the size and behavior of the material being retained or passed through. For guards and partitions, evaluate access control, rigidity, edge treatment, and how the panel will be fixed. If the panel is intended to carry load or protect people from machinery, the complete assembly should be assessed by a qualified project engineer rather than relying on mesh dimensions alone.

SS304 is one material option, but buyers may also compare other stainless grades or non-stainless materials where corrosion exposure, budget, fabrication, or project standards make them relevant. The correct comparison depends on the actual environment and service life expectations. Shunqiang Wire Mesh can review the requested specifications and discuss available material and fabrication options for the project.

How to Select the Right Panel

Use a Clear Specification Checklist

1. Define the mesh dimension: State whether 2.36 inches is the clear opening or center-to-center pitch, and identify both mesh directions.
2. Set wire and panel dimensions: Provide the required wire diameter, panel width and length, and any dimensional tolerance required for installation.
3. Describe the application: Explain whether the panel is used for screening, guarding, separation, support, or another purpose, including relevant loads or exposure conditions.
4. Specify fabrication and finish: List edge treatment, cutouts, bends, frames, surface expectations, and packaging requirements.
5. Confirm documentation and logistics: Ask about material identification, drawing approval, minimum order quantity, production lead time, packing, and shipping terms.

Check Fit Before Comparing Quotations

When reviewing supplier offers, compare the complete specification rather than price per panel alone. Check that each quotation uses the same interpretation of the mesh dimension, wire diameter, material grade, panel size, quantity, and finishing scope. A lower price may reflect a different specification, omitted fabrication, or different packing assumptions.

Request a drawing or written specification for approval before production, especially for repeat orders or panels that must fit a prepared frame. Confirm how the supplier handles dimensional tolerances and what inspection information is available. These checks help align the delivered product with the project requirement without relying on an unclear product label.

Pricing, MOQ, and Lead Time

The price of a welded mesh panel can depend on material grade, wire diameter, panel dimensions, order quantity, fabrication, finishing, packaging, and delivery destination. Minimum order quantity and lead time may vary with the requested specification and production schedule. We therefore recommend requesting a project-specific quotation rather than relying on a general price estimate.

To support an accurate quote, send a drawing or list the mesh measurement basis, wire diameter, panel size, required quantity, material grade, and destination. Include the required delivery date and any inspection or documentation needs. If specifications are still being developed, identify which details are fixed and which can be discussed with the supplier.

Supplier Evaluation Checklist

• Can the supplier clearly explain whether the 2.36 inch dimension refers to aperture or pitch?
• Will the quotation list material grade, wire diameter, panel dimensions, and fabrication details?
• Can the supplier provide a drawing or specification for approval before production?
• Are MOQ, lead time, packaging, shipping scope, and available material documents stated clearly?
• Does the supplier invite discussion of the intended environment and application rather than assuming one specification fits all?

At Shunqiang Wire Mesh, we support B2B buyers by reviewing requested mesh dimensions, panel sizes, material requirements, and fabrication details for quotation. Share your drawing or project specification so our team can clarify the measurement basis and confirm the available supply options. Final product suitability should be assessed against your installation, operating conditions, and applicable project requirements.

Conclusion: Is a 2.36 Inch SS304 Panel Right for Your Project?

A 2.36 inch SS304 welded wire mesh panel may suit projects that need a relatively open, rigid stainless steel grid, provided its opening, wire diameter, panel size, and material are appropriate for the application. The key first step is to define whether 2.36 inches means clear opening or center-to-center spacing. Then verify the service environment, fabrication details, and fit before comparing supplier quotations.

For your next step, prepare a drawing or specification with the mesh measurement basis, wire diameter, panel dimensions, quantity, finish, and delivery destination. Send those details to Shunqiang Wire Mesh to request a project-specific review and quotation. Clear requirements make it easier to assess whether the panel matches your application and sourcing needs.

The company is the world’s best 2.36 inch ss304 welded wire mesh panel supplier. We are your one-stop shop for all needs. Our staff are highly-specialized and will help you find the product you need.