D21.5×T2 Laser Protective Lens: Specifications and Compatibility Guide
A D21.5×T2 laser protective lens is generally specified as a flat protective window with a nominal diameter of 21.5 mm and a thickness of 2 mm. Those dimensions alone do not confirm that it will fit or perform correctly in a particular laser head: the material, wavelength range, coating, tolerances, edge profile, and holder design also matter. I recommend checking the equipment drawing or the existing lens before ordering, then confirming the complete specification with the supplier. This guide explains what to verify and how to assess compatibility.
Key Takeaways
- D21.5×T2 usually describes nominal dimensions: 21.5 mm diameter by 2 mm thickness. Confirm the drawing convention and tolerances before purchase.
- Dimensions are only one part of compatibility: wavelength, optical material, coating, mounting, and operating conditions should also match the application.
- Do not infer equipment fit from the size code alone: compare the part with the machine documentation or a measured original.
- Request written confirmation: share the lens drawing, laser parameters, and intended use with the supplier before placing an order.
Who This Guide Is For
This guide is for purchasing teams, machine builders, maintenance technicians, and distributors sourcing a D21.5×T2 laser protective lens. It is useful when replacing a damaged window, checking a proposed spare part, or comparing supplier quotations. It is also relevant when a size code appears to match but the original lens material or coating is unknown. The guide is not a substitute for the laser equipment manufacturer’s instructions.
What the D21.5×T2 Specification Means
Nominal diameter and thickness
In common optical component notation, “D” refers to diameter and “T” refers to thickness. On that basis, D21.5×T2 indicates a nominal diameter of 21.5 mm and a nominal thickness of 2 mm. However, suppliers and drawings may use different conventions, so buyers should verify the units and the meaning of the code against a technical drawing.
Nominal dimensions do not state the permitted dimensional variation. A lens may require a specified diameter tolerance, thickness tolerance, flatness, or edge treatment to seat correctly in its holder. Ask for the drawing or written dimensional specification rather than assuming that every product carrying the same size code is interchangeable.
Material, coating, and optical properties
Protective windows may be supplied in different optical materials, with material choice depending on the laser wavelength, power conditions, environment, and equipment design. Fused silica is one material buyers may encounter in laser optics, but its suitability should not be assumed for every machine or operating condition. Confirm the material grade and applicable wavelength range for the intended application.
A coating may be specified to manage reflection or transmission at a particular wavelength, while some applications may call for an uncoated window. Coating choice is not simply a cosmetic detail: a mismatch can affect optical performance or service life. Ask whether the coating is single-sided or double-sided, which wavelength range it is designed for, and which surface should face the laser when orientation matters.
Compatibility: What to Check Before Ordering
1. Confirm the mechanical fit
Compare the lens diameter and thickness with the equipment drawing, replacement-part information, or a carefully measured original component. Check whether the holder uses a retaining ring, gasket, stepped seat, or another arrangement that affects usable dimensions. Also ask whether the lens has a chamfer, bevel, or other edge feature that is not included in the basic D21.5×T2 description.
2. Match the optical requirements
Identify the laser wavelength and confirm that the material and any coating are specified for it. For example, 1064 nm may be relevant to some laser systems, but it is only an example and does not establish compatibility with a particular D21.5×T2 lens. If the system uses more than one wavelength or operates across a defined wavelength range, provide that information to the supplier.
QIRUI LASER contains other products and information you need, so please check it out.
3. Review operating conditions and assembly details
Share the equipment type, expected operating conditions, and the lens position in the optical path. Thermal load, contamination, cleaning practices, and airflow can influence the requirements, but their effects depend on the system design. Confirm installation direction and handling instructions from the equipment or lens supplier; avoid touching optical surfaces directly during inspection or replacement.
4. Confirm replacement-part equivalence
If replacing an existing lens, do not rely on appearance alone. Record any part number, material marking, coating information, and drawing reference, and compare those details with the proposed replacement. When documentation is unavailable, send clear photographs and measured dimensions to the supplier, while noting that photographs cannot establish material or coating characteristics.
Buyer Selection Framework
| Specification to verify | Why it matters | What to request |
|---|---|---|
| Diameter and thickness | Determines whether the lens can fit the holder as intended. | Dimensioned drawing, units, and tolerances. |
| Material | Must suit the optical and operating requirements of the system. | Material name or grade and relevant specification. |
| Wavelength and coating | Influences whether the optical surface is appropriate for the laser. | Specified wavelength range, coating details, and orientation. |
| Surface and edge details | Can affect handling, mounting, and optical performance. | Surface-quality requirements and edge or chamfer details, if specified. |
| Traceability and inspection | Helps buyers review product identity and incoming goods. | Available inspection documentation and lot identification information. |
Pricing, MOQ, and Lead-Time Considerations
Pricing for a D21.5×T2 lens depends on the confirmed material, coating, tolerances, documentation needs, order quantity, and packaging requirements. A standard configuration and a custom specification may be quoted differently, so compare quotations only after aligning the technical details. Do not assume that a lower price covers the same coating, inspection scope, or dimensional tolerances.
Minimum order quantity and lead time should be confirmed for the exact configuration and requested quantity. Availability can vary with material, coating, production scheduling, and whether the item is standard or made to a drawing. For a purchase plan, request the quote validity, estimated dispatch schedule, MOQ, packaging method, and any sample or pre-production options in writing.
Supplier Evaluation Checklist
Before approving a supplier, check whether they can respond clearly to the technical questions behind the size code. A useful supplier should be able to review a drawing or application specification, identify missing information, and state what is included in the quoted configuration. Buyers should also establish how dimensions and product identity will be checked before shipment.
- Can the supplier confirm that D21.5×T2 means 21.5 mm diameter by 2 mm thickness for the offered part?
- Can they provide a drawing with tolerances and relevant edge details?
- Are material, wavelength range, coating, and coated-side orientation clearly stated?
- Can they explain available inspection records, packaging, MOQ, and lead time?
- Will changes to the approved specification be communicated before production or shipment?
How QIRUI LASER Can Support Your Evaluation
At QIRUI LASER, we can review a D21.5×T2 inquiry against the information you provide and help clarify which details need confirmation before sourcing. To make the discussion more productive, share the equipment model or lens drawing, the required dimensions and tolerances, the laser wavelength, coating requirements, and order quantity. If some specifications are unknown, identify them as unconfirmed rather than treating a size-code match as proof of compatibility.
We recommend requesting a written specification and quotation for the exact configuration under consideration. This gives your engineering and purchasing teams a clear basis for checking fit, optical requirements, order terms, and incoming inspection criteria. Final suitability should be verified against the equipment manufacturer’s requirements and the confirmed product documentation.
Conclusion
A D21.5×T2 laser protective lens generally refers to a lens with a nominal diameter of 21.5 mm and a thickness of 2 mm, but the code alone cannot establish compatibility. Before ordering, confirm the dimensional tolerances, material, wavelength range, coating, mounting details, and operating requirements. The practical next step is to send your drawing or existing-part details to the equipment provider or supplier and request written confirmation of the proposed specification. Contact QIRUI LASER with your application and purchasing requirements to discuss the configuration and quotation process.

Comments
0