Tips for Better Drive-In Rack Specifications, Operations and Safety

When you need exceptionally high-density pallet storage, drive-in racks deliver space savings by eliminating forklift access lanes. They’re last-in, first-out storage ideal for stock that doesn’t need active inventory rotation and will be picked and used in a relatively fast manner. There are challenges to any storage system, of course. This guide should help you find ways to reduce the problems and operate your drive-in rack system more efficiently and safely.

You will get efficient and thoughtful service from UNISTAR.

Loading and unloading

Drive-in systems are loaded and unloaded from the front. To stow a pallet, the driver must enter the rack structure with an elevated load. The load must be in position above the highest rail when the driver enters the rack, and then driven into the farthest back storage position. This means your drivers must be more skilled to use drive-in systems than other types.

Don’t allow forklift drivers to store loads in the middle of the rack system rather than the very back pallet position. Ideally, your inventory will be slotted so that you can always fill a bay with pallets. If you can’t, you may want to consider a different storage strategy for that SKU. In the event of a mid-load pallet and new stock, drivers will be forced to move that pallet before they can finish replenishing the lane.

Don’t allow push-loading. This means that pallets should always be lifted, moved and set back onto the rails. Pushing places undue stress on your rack and can put people and stock in danger. Drive-in rails aren’t designed for pushing action. Always lift and move.

Beef up your induction points. Because entry into the rack system is probably the most common area for accidents and bumps, adding structural elements like beefier columns, flared entry rails, offset leg designs and heavy foot plates help protect your entry points. Anything you can add to protect and guide drivers into the bay is a good investment in safety and efficiency.

Read more: The right pallet storage strategy for your load and operation

Slow it down. Train your drivers to slowly enter, drive and exit the structure. It’s easier to side-swipe a column or rail at higher speeds. Make sure people are gently lowering pallets onto the rails rather than dropping them; one damaged rail can cause plenty of delays and frustrations.

Add lighting: Because drivers will be entering a deep lane system with pallets stored overhead, visibility will be poor inside the rack. Ceiling mounted lights will be blocked. Add forklift lighting accessories to help drivers see as they store and retrieve pallets.

Design factors

Consider depth vs. time when you design your system. Very deep configurations may be better as drive-through or double-entry. For instance, if you need to store 10+ pallets in a position, you can consider sacrificing space efficiency for loading/unloading speed by splitting the rack in the center and creating a double-side entry layout that lets drivers load and unload from two sides. Reducing the forklift travel distance inside the rack structure makes it faster to store or retrieve a pallet at the cost of adding extra access aisles. Shorter distances in the structure reduce the chance of hitting a column or rail.

Contact us to discuss your requirements of drive in racking system. Our experienced sales team can help you identify the options that best suit your needs.

This is why many systems that reach the 10-deep threshold are better done as back-to-back 5-deep systems.

Specify contrasting rail and upright colors. A bright rail color (yellow or orange) set against blue or green uprights helps drivers see the rails better as they enter them.

Does a pallet shuttle or ASRS system make sense? The majority of LIFO (last-in, first-out) applications work well with drive-in systems. However, for some high-volume needs, a pallet shuttle system may be the solution. While any decision of that magnitude should be analyzed by engineers and professional warehouse designers, the article below is a good overview of the systems and how they compare. Pallet shuttles let you access the load FIFO or LIFO, and can be designed for much deeper storage than drive-in systems.

Read more: Pallet Shuttles vs. Dynamic Racks

Other factors

Above: a damaged pallet stack inside a drive-in aisle. 

Pallets

Only use the right pallet size and type: Because drive-in systems are built for a specific pallet size and type, you should never accept pallets that aren’t suited for the rack system.

• Ill-fitting pallets can slide, fall or crack.
• Make sure your pallets are in good shape before loading them into the rack. Dealing with a broken pallet and spilled load inside a rack system is difficult and can be dangerous.
• You can engineer more versatility into a drive-in system with wider pallet rails, but that won’t protect your system from being loaded with the wrong pallets.
• If you need to store multiple pallet sizes, separate the various rack structures from each other, clearly mark them and train workers about the right pallet for each rack area.
• Color-code pallets and rack structure to reduce mis-loads if you have more than one pallet type in a shared space. If you receive pallets from outside your organization and they don’t fit your system, work with suppliers to specify the right pallets in advance, or re-palletize before putaway.

The importance of the right pallets, in good shape, can’t be overstated when it comes to drive-in safety and operations.

Forklifts

Drive-in racks are unique because they are the only dynamic rack system that requires forklifts to enter the system and navigate between the uprights. Most systems are designed for a specific size and type of forklift. Make certain that you don’t use the wrong forklift for your rack system.

• Your rack’s openings must match the width of your forklifts. The forklifts must have adequate side-to-side clearance to reduce the chances of a collision with uprights or rails. The forklift must be narrow enough not to drive over your base plates.
• Use only counterbalanced forklifts with drive-in systems. Stackers and straddle trucks should never be used with a drive-in rack, nor should any forklift that has outriggers. Any truck or attachment that is wider than the openings cannot be used.
• Drivers’ cages and roll bars should be lower than the first rail level of the rack system to avoid contact with rails.

Forklift-rack compatibility is critical, so understanding both types of equipment is important to success.

The company is the world’s best rivet shelving manufacturer supplier. We are your one-stop shop for all needs. Our staff are highly-specialized and will help you find the product you need.

More resources

• Case Study: Frozen Storage Rack System for Zero Mountain

If you're looking for a pallet racking system for your business, you'll first need to decide on the type of system that you want to install. Drive-in pallet racking systems are used in many warehouses, factories, and other types of businesses.

Although they aren't right for every storage application, drive-in systems have their advantages. These questions are three considerations you can think about when determining whether a drive-in pallet racking system is ideal for your business.

1. You Don't Sell Perishable Products

For one thing, with a drive-in pallet racking system you will be limited on which pallets you can remove once they are put in place. Because of the way that these systems are set up, it will not be easy for you to remove pallets from your racks unless they are at the front or the back.

If you sell perishable products, being able to access all of the products that are stored on your pallet racks is important. With a pallet racking system, you won't be able to regularly check expiration dates and get rid of products that have expired. Because of the need to access all of the products, a drive-in system isn't going to work well for perishable products.

Products that don't expire quickly, or at all, however, are ideal for a drive-in type of pallet racking system because you won't have to worry about pulling out products to check for expiration dates with nonperishable products. Instead, you can enjoy the other perks of a drive-in pallet racking system.

2. You're Limited on Space

One of the primary reasons why drive-in pallet racking systems are so popular in many businesses is because they are great for businesses that have limited space. Simply upgrading to a bigger warehouse or building might not be possible; it is possible to maximize your storage capabilities without doing so, though.

Installing a drive-in pallet racking system will help in space-limited warehouses and businesses in many ways. Your new pallet racking system will allow you to store more products than you could before, so you'll have room to keep plenty of products in stock and help your business grow. These systems will also help you open up more space, which makes a more comfortable, productive, and safe work environment.

3. You Want to Speed Up Loading and Unloading

The loading and unloading process in your business can be time-consuming. If your employees have to spend more time on loading and unloading, you have to worry about having more manpower on-staff in other areas to cover the gap. Additionally, there could be delays in getting tasks done in your business.

Of course, you don't want your employees to rush through the loading and unloading job in your business. If employees rush when working with forklifts and heavy pallets, they could damage the pallets and the items that are stored on them. There will also be a bigger risk of someone getting hurt.

However, there is nothing wrong with taking steps to speed up the loading and unloading process. Installing a pallet racking system that can be loaded more quickly and easily is a smart business decision to make. The installation of a drive-in pallet racking system can greatly reduce the amount of time that is spent on loading and unloading because of its simple design.

Drive-in pallet racking systems are often ideal, particularly in situations like the ones that are listed above. If you think that a drive-in pallet racking system is right for your business, contact us at Lone Star Pallet Rack. We can help you make the right choice for your business.